export@civilmechanicalindia.com Exporting to 90+ countries IS · BS · EN · ASTM · AASHTO

Roll Driven Slipout Type Bending Rollers Manufacturers and Suppliers in India

Roll Driven Slipout Type Bending Rollers Suppliers

Quick answer: Roll driven slipout type bending rollers shape plate, sheet, angle and pipe into curves and cylinders. The range has three roll and four roll plate bending machines, an angle ring roller, a pipe and tube bending roller and a manual sheet rolling machine. Civil Mechanical India makes these rolling machines and supplies them to workshops in India.

Boiler shops and fabricators asking for roll driven slipout type bending rollers manufacturers in India need to know plate width and thickness first. Civil Mechanical India is one of the suppliers in India that lists three and four roll plate benders, ring rollers and sheet rollers, with the slipout end that releases a finished cylinder.

Plate rolls bend metal by passing it between rollers set at an offset. In a three roll pinch type, two lower rolls and one upper roll form the curve, and the pinch grips the plate for driving. The slipout design lets the end bearing of the top roll be released so a closed cylinder can be slid off the roll.

The four roll machine adds a fourth roll so the plate can be pre-bent at both ends without turning it around, and its hydraulic side rolls adjust the curve. The angle ring roller has grooved rolls to bend angle and flat bar into rings. The pipe and tube roller has grooved rolls and a motor, and the manual sheet rolling machine uses a hand crank for thin sheet and ducts.

Last updated: November 2026

Angle Ring Bending Roller

Product code: CMI-NP-0732
Buy Angle Ring Bending Roller from India

Angle Ring Bending Roller is a three roll machine with grooved rolls for bending angle and flat bar into rings, designed for forming rings and curved frames from angle iron and flat bar.

Four Roll Plate Bending Machine

Product code: CMI-NP-0733
Buy Four Roll Plate Bending Machine from India

Four Roll Plate Bending Machine is a four roll plate bending machine with hydraulic side rolls, designed for pre-bending and rolling plate with minimal flat ends.

Manual Sheet Rolling Machine

Product code: CMI-NP-0734
Buy Manual Sheet Rolling Machine from India

Manual Sheet Rolling Machine is a hand crank rolling machine with three rolls for thin sheet, designed for rolling light sheet and wire-edge forms in sheet metal training.

Pipe and Tube Bending Roller

Product code: CMI-NP-0735
Buy Pipe and Tube Bending Roller from India

Pipe and Tube Bending Roller is a pipe bending roller with grooved rolls and motor drive, designed for bending pipes and round tubes to a given radius.

Three Roll Plate Bending Machine

Product code: CMI-NP-0736
Buy Three Roll Plate Bending Machine from India

Three Roll Plate Bending Machine is a motor driven three roll pinch type machine for rolling steel plate into cylinders, designed for bending mild steel plate to cylindrical shells in fabrication workshops.

Roll Driven Slipout Type Bending Rollers range by function

FunctionProductsWhat to confirm
Plate rollingThree Roll Plate Bending Machine, Four Roll Plate Bending MachinePlate width and thickness, top roll diameter, minimum rolling diameter and pre-bending capacity
Section and pipe rollingAngle Ring Bending Roller, Pipe and Tube Bending RollerSection sizes, roll groove profiles, ring diameter range and motor drive
Light sheetManual Sheet Rolling Machine, Roll Driven Slipout Type Bending RollersSheet width and gauge, hand or motor drive, and roll diameter

How is this different from Hydraulic Pipe Bending?

Hydraulic pipe benders push a pipe around a former at one spot for a sharp, localised bend. Bending rollers pass material through rolls in successive steps to make a large radius curve, a ring or a full cylinder. Choose the pipe bender for elbows in conduit and tube, and the bending roller for shells, rings and wide, gentle arcs.

See also: Hydraulic Pipe Bending Suppliers

Full Roll Driven Slipout Type Bending Rollers product list

The complete Roll Driven Slipout Type Bending Rollers range (6 products), in alphabetical order:

Specifications and standards

How do I specify width, thickness and diameter?

State the widest plate, the thickest plate and the smallest cylinder diameter. Capacity falls for narrower diameters and harder material. The machine rating is normally for mild steel at a stated width. Ask for the rating at your actual plate.

Three roll or four roll?

A three roll machine is cheaper and fine for most work, but leaves flat ends unless the plate is pre-bent. A four roll machine pre-bends and rolls in one setting and gives better accuracy, at a higher price. Choose by the quality and volume of cylinders.

What drive and safety features are important?

Check gearbox type, motor kW, roll surface hardness, foot pedal control and emergency stops. Rolls should be guarded at the nip. A support arm for long plates reduces operator strain. Also ask for a guard around the roll nip, because the rolls trap clothing and fingers, and an emergency stop within easy hand reach.

Who buys Roll Driven Slipout Type Bending Rollers?

Pressure vessel and boiler shops, tank and silo makers, structural fabricators, duct and chimney makers, ITIs and polytechnic fabrication labs buy these machines. A manual sheet roller is common in school workshops. Chimney and duct workshops also use them for making cylindrical sections, and small ring rollers serve gate and grill makers.

Related ranges

Frequently asked questions

What does slipout mean?

The end support of the top roll swings or slides out so a rolled cylinder can be taken off the roll. A tilting bearing housing frees one end of the top roll, so the finished ring can be slid off the roll, which is impossible on a closed frame.

Can the machine roll cones?

Yes with skilled setting and a tilted top roll on some models. Mention it when ordering. For tapered shells the top roll is tilted or the plate is fed at an angle, and many models cannot do this, so confirm it for your job.

How is roll hardness specified?

Rolls are usually surface hardened to resist marking. Ask for hardness in HRC. Hard chrome or hardened steel rolls resist marks, and the hardness is usually in the range of 50 to 55 HRC, which should be written in the quotation.

What is pre-bending?

Bending the plate ends before rolling, so the finished cylinder does not have flat spots. A pre-bent end saves the flat portion that remains when a plate is rolled between the rolls, and four roll machines do this in one setting.

Do you provide supply for tenders?

Yes, with drawings and technical details. For tender supply we prepare a technical sheet with roll diameter, plate capacity and motor details, and give drawings with the quotation.

Tender enquiries

Request a tender quotation

Civil Mechanical India is an established manufacturer and supplier for tender requirements from India, handling civil laboratory and industrial testing tenders and bulk and OEM orders for mechanical engineering and testing laboratory equipment. On receipt of your tender specifications, we will submit a complete quotation for Roll Driven Slipout Type Bending Rollers.

  • Civil laboratory & industrial testing tenders
  • Mechanical engineering & testing lab equipment
  • Bulk and OEM supply
Send Tender Specifications Quotation prepared against your tender specifications
Get a quotation

Planning a civil engineering laboratory or replying to a tender?

Send us your equipment list or tender specification. We quote against IS, BS, EN, ASTM and AASHTO standards and ship to 90+ countries.