Cement-mortar testing equipment manufacturers in India supply instruments that cement plant labs use hour by hour for batch release. Civil Mechanical India is one of the suppliers in India offering automatic versions of the standard tests, so setting time, strength and fineness results are produced consistently across shifts.
The group follows the life of a cement sample. Fineness is found with the Blaine air permeability apparatus; consistency and setting time with the Vicat apparatus; and soundness with the Le Chatelier set. Mortar is then prepared on the jolting table, checked for flow and water retention, moulded into prisms and cubes, and crushed on the flexural and compressive machines.
Special instruments measure shrinkage and length change for repair mortars and the tensile adhesion strength of tile adhesives. Plant labs mostly run the core tests daily, whereas product development labs use the specialised ones.
Last updated: November 2026
Digital Blaine air permeability apparatus that measures the specific surface area of cement and fine powders by timing air flow through a compacted bed. Used for fineness control in cement grinding plants.
Automatic hydraulic compression machine with 250 kN capacity for crushing 70.6 mm and 50 mm mortar cubes at standard loading rate. Used for cement strength grade testing in plant labs.
Motorised Vicat needle apparatus that automatically penetrates cement paste at set intervals to find consistency and initial and final setting time. Used in cement plant QC labs and ready-mix testing.
Electromechanical bending machine with three-point roller fixture that breaks 40 x 40 x 160 mm mortar prisms at a constant load rate to give flexural strength. Used in cement plant and building material labs.
Le Chatelier moulds with a thermostatic boiling water bath to determine the volume expansion of cement due to free lime and magnesia. Used in cement plants and receiving labs for soundness checks.
Motor driven flow table that jolts a mortar cone 25 times in 15 seconds for flow and workability testing of cement mortar and masonry mix. Used in cement and mortar plant labs.
Dial-gauge length comparator with reference bar for measuring drying and autogenous shrinkage of mortar prisms over time. Used in cement, repair mortar and grout development laboratories.
Vacuum water retention apparatus with pressure-type air meter for fresh mortar, plaster and masonry mixes. Used for QC of ready-mix mortar, dry premix and plaster products.
Standard jolting apparatus that compacts mortar prisms 40 x 40 x 160 mm with 60 jolts for cement strength tests. Used in plant labs following EN 196-1 mortar preparation.
Pull-off tester with motorised loading and digital peak display for tensile adhesion strength of tile adhesives, renders and mortar on substrate. Used in construction chemicals QC and site labs.
| Function | Products | What to confirm |
|---|---|---|
| Physical properties of cement | Air Permeability Blaine Apparatus for Cement Fineness, Automatic Vicat Apparatus with Digital Penetration Timer, Le Chatelier Soundness Test Set with Heating Bath | Standard cell and manometer fluid, needle and plunger set, bath heating time to boil, and method such as IS 4031 or EN 196 |
| Mortar preparation and workability | Mortar Flow Table with Motorised Drop Mechanism, Standard Jolting Table for Mortar Prism Moulds, Mortar Water Retention and Air Content Tester | Table diameter, drop height and speed, mould size, counter and automatic stop, and sample vessel volume |
| Strength testing | Automatic Compressive Strength Machine for Cement Mortar Cubes, Flexural Strength Machine for Mortar Prisms 10 kN | Capacity in kN, rate of loading control, platen size, cube or prism size and printout or data output |
| Special mortar properties | Mortar Shrinkage and Length Change Comparator, Tile Adhesive Tensile Adhesion Strength Tester | Gauge resolution, specimen length, pull-off speed and the product standard, for example IS 15477 or EN 12004 |
Cement-mortar equipment is purpose built around specified moulds, needles, tables and loading rates, and gives a result that is directly comparable with a cement standard. General lab equipment such as ovens, balances and baths is material-neutral and supports many tests. A cement lab needs both: the specific machines for each test and the general units that condition and weigh the samples.
See also: General Lab Testing Equipment
The complete Cement-Mortar Testing Equipment range (10 products), in alphabetical order:
Verify the governing standard, for example IS 4031 parts, IS 650 sand, ASTM C109 or EN 196, because cube and prism sizes and loading rates differ. Check machine capacity against the highest cement grade, automatic load rate control, safety guards, and whether moulds, standard sand and a calibration proving device are supplied.
A plant releasing cement each shift benefits from automatic loading, peak hold and results storage, because loading rate controls the result. Manual machines are acceptable for low-volume or backup use. Ask for a calibration certificate and an option for a compression test on concrete cubes if the lab also serves ready-mix.
Cement labs need a temperature-controlled room around 27 deg C and a humidity cabinet or curing tank. Strength machines weigh several hundred kilograms and require a levelled floor. Plan 230 V single phase for balances and baths, 415 V for large machines, and drainage for water used in moulding and curing.
Cement manufacturers, ready-mix and precast producers, tile adhesive and repair mortar makers, construction chemical companies, and third-party construction labs place orders. Buyers typically order a full cement set for a plant lab: fineness, consistency, soundness, strength and the mortar preparation tables, together with a curing tank and balance from the general lab range.
It measures the specific surface of cement, reported in square metres per kilogram, by timing the passage of air through a compacted bed of powder. Fineness is a quality parameter that links to strength gain and fixes the grinding performance of the mill.
Yes. Automatic versions lower the needle at set intervals, record penetration and give initial and final setting times without constant attention, which frees the technician and removes reading differences between operators.
Yes. Civil Mechanical India supplies plant labs, research units and test houses across India and can provide a complete lab package. Delivery, installation and training depend on location and are confirmed in the quotation.
Instruments are built for Indian standards such as IS 4031 and IS 5512, as well as ASTM and EN equivalents. Mention the one your customers audit you against so that moulds, loading rates and tolerances are matched.
Yes. Export orders are packed for shipment with documentation and can be configured for different voltages. Share the destination country and required standard when you ask for the quotation.
Civil Mechanical India is an established manufacturer and supplier for tender requirements from India, handling civil laboratory and industrial testing tenders and bulk and OEM orders for mechanical engineering and testing laboratory equipment. On receipt of your tender specifications, we will submit a complete quotation for Cement-Mortar Testing Equipment.
Send us your equipment list or tender specification. We quote against IS, BS, EN, ASTM and AASHTO standards and ship to 90+ countries.
