Power Electronic Automation Control Training System
Product code: CIVIL-PEA-174-0001Buy Power Electronic Automation Control Training System from India
Power Electronic Automation Control Training System
Electrical departments looking for Power Electronic Automation Control Training System manufacturers in India want converters that are controlled the way industry controls them, by PLC or microcontroller, with protection built in. Civil Mechanical India builds inverter, rectifier, SMPS and solar trainers, and is among the suppliers in India with a PLC-linked power electronics range.
Each trainer demonstrates one family of converters. The IGBT inverter and DC chopper trainer is PLC controlled for studying PWM, frequency and voltage control of motors and loads. The three-phase unit has a thyristor converter module for controlled rectification, firing angle control and DC motor drive operation. The switched mode power supply system includes buck, boost and flyback sections with a PLC or microcontroller for DC-DC conversion and automatic regulation.
The soft starter and drive panel compares DOL, soft start and VFD starting on an induction motor with PLC sequencing, and the solar system has a PV simulator, MPPT charge controller, battery and inverter for automatic power management. Check converter ratings, isolation, available scope points, PLC make and whether a differential probe is supplied.
Last updated: November 2026
Power Electronic Automation Control Training System
Trainer with an IGBT inverter and DC chopper that a PLC controls for studying PWM, frequency and voltage control of motors and loads. Key highlights include iGBT inverter and chopper modules and pLC generated PWM.
Panel with a soft starter, DOL and VFD options for comparing starting methods, current and torque on an induction motor with PLC sequencing. Key highlights include soft starter with ramp settings and dOL and VFD comparison.
System with a PV simulator, MPPT charge controller, battery and inverter to teach automatic power management in solar installations. Key highlights include pV simulator supply and mPPT charge controller.
System with buck, boost and flyback converter sections and a PLC or microcontroller for studying DC-DC conversion and automatic voltage regulation. Key highlights include buck, boost and flyback sections and duty cycle control.
Unit with thyristor converter module controlled by a PLC to teach controlled rectification, firing angle control and DC motor drive operation. Key highlights include thyristor bridge with firing control and pLC set point control.
| Function | Products | What to confirm |
|---|---|---|
| Inverters and choppers | PLC Controlled Inverter and Chopper Power Electronics Trainer | IGBT module rating, switching frequency and PLC link |
| Soft starters and drives | Soft Starter and Motor Drive Automation Training Panel | motor kW, VFD and DOL options |
| Solar power electronics | Solar Charge Controller and Inverter Automation Training System | PV simulator rating and the MPPT controller |
| Rectifiers and SMPS | Three Phase Rectifier and Converter Automation Control Training Unit, Switched Mode Power Supply Automation Training System | thyristor module, converter type and the output ratings |
The electronic and electric drive system concentrates on complete drive trainers: DC, servo, stepper, VFD and soft starter with a motor and load. The power electronic automation system looks inside the converter: IGBT and thyristor switching, PWM, firing angle, SMPS topologies and MPPT, all controlled by a PLC or microcontroller. Students normally study converters first, then drive trainers that use them in complete motor systems.
See also: Electronic and Electric Drive Training System for Electrotechnic
The complete Power Electronic Automation Control Training System range (6 products), in alphabetical order:
Check the converter voltage and current ratings, whether the supply is isolated through a transformer, the scope test points, the switching frequency range and the controller. Ask about protection against short circuits and overheating, and shrouded sockets. A differential or isolated probe is important to avoid damaging oscilloscopes and students' safety.
Students vary the firing angle from a PLC and watch the output voltage of a three-phase controlled rectifier change, then connect a DC motor to see speed regulation. They observe waveforms, ripple and the effect of inductive loads. Ask for the supply voltage, the load rating and the way firing pulses are generated and displayed.
It shows maximum power point tracking, charge control and inverter operation using a PV simulator, so students can run experiments in any weather. It links power electronics with renewable energy courses. Ask for the PV simulator power rating, the battery type and the inverter output waveform.
Electrical and electronics engineering colleges, polytechnics with power electronics and drives courses, renewable energy institutes and corporate training academies buy these trainers. Research labs use the SMPS and inverter units for prototype work. A typical purchase includes the inverter and chopper trainer, the thyristor unit and an SMPS system, so that AC, DC and switching converters are all covered.
It has buck, boost and flyback converter sections with a PLC or microcontroller for DC-DC conversion and automatic voltage regulation, which lets students compare topologies on the same board.
The PLC controlled IGBT inverter and DC chopper trainer is used to study PWM, frequency and voltage control of motors and loads, so students watch how the output changes with commands.
The soft starter and motor drive panel compares DOL, soft starter and VFD options on an induction motor with PLC sequencing, showing differences in current and torque.
It uses a PV simulator supply, so MPPT charge control, battery charging and inverter output can be demonstrated indoors at any time. Ask for the PV simulator rating.
Yes, we handle overseas orders on request. Please give the grid voltage and frequency so that transformers and converter ratings are matched to your lab.
Civil Mechanical India is an established manufacturer and supplier for tender requirements from India, handling civil laboratory and industrial testing tenders and bulk and OEM orders for mechanical engineering and testing laboratory equipment. On receipt of your tender specifications, we will submit a complete quotation for Power Electronic Automation Control Training System.
Send us your equipment list or tender specification. We quote against IS, BS, EN, ASTM and AASHTO standards and ship to 90+ countries.