Shoe buyers and certifiers want test reports on sole wear, bond and safety toe caps before a lot is shipped. Our footwear testing instruments reproduce the standard tests at factory scale. As footwear testing instruments manufacturers in India and suppliers in India, we supply shoe plants, safety footwear makers and sole material labs.
The range follows how a shoe fails. Wear and flexing are checked on the abrasion drum tester, sole flexing tester and whole shoe flex fatigue machine in a temperature chamber. Safety is checked on the toe cap compression frame and the toe cap impact tester, and slip resistance on a force plate machine. Construction is tested by bond strength peel testers and the heel strength tester. Water behaviour is checked on the upper penetration tester and insole absorption tester.
Export shoe units normally build up gradually, starting with abrasion, bond and flexing tests and then adding the safety toe cap and slip tests.
Last updated: November 2026
Rotating drum abrader measuring volume loss of shoe sole material against an abrasive sheet. Used for outsole rubber, PU and TPU material approvals. The relative volume loss figure is a standard criterion in shoe specifications.
Tests the ability of insole materials to absorb and release perspiration. Used by insole, sock lining and shoe producers. It gauges how comfortably insoles handle sweat during long wear.
Machine pressing a shoe onto a wet tile with controlled load and sliding speed, measuring friction coefficient. Used for safety and occupational footwear certification labs.
Machine that repeatedly flexes shoe soles to the standard angle and counts cycles until cracks appear. Used by footwear factories and shoe test labs. It simulates walking stress on rubber, PU and PVC soles under repeated bending.
Flexes whole shoes in a temperature-controlled chamber to test durability at cold and hot extremes. Used by sports, safety and hiking footwear brands. It is useful for testing shoe durability for cold climate markets and hot work sites.
Compression frame that squeezes toe caps to 15 kN, measuring remaining height. Used for steel and composite toe protective footwear. The result confirms the cap holds its shape under a 15 kN crushing load.
Falling mass tester that drops a striker onto steel toe caps to measure clearance under impact. Used in safety shoe manufacture and certification. It checks that toe protection survives a 200 J strike while leaving enough room.
Tests the pull-off strength of heel attachments and heel tip retention in shoes. Used by footwear manufacturers and quality labs. It verifies that heels remain fixed under pulling and leverage in wear.
Flexing water tester that measures how long uppers resist water penetration and water uptake. Used for leather, textile and safety boots. It supports claims for waterproof footwear used in rain, wet floors and farms.
Tensile machine with footwear grips measuring adhesion between upper and sole, stripped to a set peel angle. Used to check cement, direct injection and vulcanised bonding. It supports production checks on cemented, vulcanised and injection-moulded shoes.
| Function | Products | What to confirm |
|---|---|---|
| Wear and flex durability | Footwear Abrasion Resistance Tester for Outsoles with Rotary Drum, Footwear Sole Flexing Resistance Tester, Footwear Whole Shoe Flex Fatigue Tester with Environmental Chamber | Drum size and abrasive sheet, bend angle and speed, chamber temperature and the number of stations. |
| Safety footwear tests | Safety Footwear Compression Test Machine for Toe Caps, Safety Footwear Toe Cap Impact Tester | Compression load up to 15 kN, impact energy of 200 J, striker geometry and clearance gauge needs. |
| Slip and bond performance | Footwear Slip Resistance Testing Machine with Force Plate, Shoe Upper and Sole Bond Strength Peel Tester, Shoe Heel Strength and Attachment Tester | Force plate range, test surface and lubricant, load cell and grip type for peel and pull-off tests. |
| Water and comfort | Shoe Upper Water Penetration and Resistance Tester, Footwear Insole Water Absorption and Desorption Tester | Flex rate and angle, penetration timing, sample sizes and the standard required. |
Footwear instruments test the finished shoe and its components, such as sole wear, toe caps, bond strength and flexing of the whole shoe. Leather instruments test the raw material, covering tensile and tear, grain crack, colour fastness, shrinkage and thickness. A shoe factory tests the leather on receipt with leather testers, and tests the finished shoes with this range.
See also: Leather Testing Instruments
The complete Footwear Testing Instruments range (10 products), in alphabetical order:
Verify that the compression frame reaches the 15 kN needed in ISO 20344 for toe cap compression with a displacement gauge, and that the impact tester delivers 200 J with the right striker. Check guards, clay cylinder or clearance measuring options, and fixtures for the shoe sizes you produce.
A rotary drum abrader with a standard abrasive sheet, defined contact load and a method to measure volume loss, as used in ISO 20344 and similar standards. Check drum speed, sample holder sizes, density measurement for volume calculation and the cleaning brush. Accuracy depends on abrasive sheet quality.
Match the bend angle, flex rate and station count to the standard you test against. Whole shoe machines in a cold chamber help to test cold flex, which is vital for winter and safety footwear. Look for easy sample mounting, a cycle counter and automatic stop.
Leather and PU shoe factories, sports and casual footwear exporters, safety shoe and gumboot manufacturers, sole and insole material suppliers, footwear design centres and accredited test labs. A first order typically includes an abrasion tester, sole flexing machine and bond strength tester, followed by safety shoe equipment and slip testing.
A shoe is pressed against a wet tile at a set force and angle and slid while the friction coefficient is recorded. The result shows how safe the sole is on wet kitchen, hospital or factory floors.
Soles flex with every step, and cracks can appear at the bend. The tester flexes soles repeatedly at a set angle and measures any cut growth after a number of cycles, which relates to product life.
A strip is cut at the joint and the two parts are pulled apart in a tensile machine fitted with shoe grips. The peel force relates to adhesive quality and surface preparation.
Yes. We manufacture the equipment in India and supply shoe plants and labs across the country and abroad. Datasheets for tenders are available, and installation and operator training can be arranged.
A flexing water tester flexes the shoe upper while it stands in water or the leather is held in a bend, and the time to water penetration or amount absorbed is recorded.
Civil Mechanical India is one of the leading manufacturers and suppliers in India for tender requirements, covering civil laboratory and industrial testing tenders and the bulk and OEM supply of mechanical engineering and testing laboratory equipment. Kindly share your tender specifications and we shall submit a complete quotation for Footwear Testing Instruments.
Send us your equipment list or tender specification. We quote against IS, BS, EN, ASTM and AASHTO standards and ship to 90+ countries.
