Wire Butt Welding Suppliers
Wire butt welding machine manufacturers in India are usually judged on how well the copper dies hold the wire and how steady the upset stroke is. Civil Mechanical India builds 10, 16, 25 and 63 kVA machines, one with an annealing circuit, and quotes against your wire gauge. We are one of the suppliers in India that sizes the transformer to the job rather than the other way round.
A butt welder heats two wire ends with heavy current, then pushes them together so the joint forms without filler. The range here is split by what is being joined. The 10 kVA and 25 kVA machines take wire and rod up to about 6 mm and 12 mm; the 16 kVA pneumatic machine adds air-cylinder clamping and upset for repeatable joints; the 63 kVA flash welder joins reinforcement bars up to 25 mm; and the annealing version softens the weld on hard wire.
Most buyers pick by the largest section they will join, since kVA and die size follow from it. A single machine often sits beside a wire drawing line to rejoin broken coils, or in a welding trade shop for resistance welding practice.
Last updated: November 2026
Pneumatic Wire Butt Welding Machine 16 kVA
Product code: CMI-NP-0925Buy Pneumatic Wire Butt Welding Machine 16 kVA from India
A pneumatic wire butt welding machine of 16 kVA with air cylinder clamping and upsetting, used for fast repeatable joints in wire rod production.
Rebar Butt Welding Machine 63 kVA
Product code: CMI-NP-0926Buy Rebar Butt Welding Machine 63 kVA from India
A 63 kVA flash butt welding machine used to join reinforcement bars up to 25 mm diameter end to end, for rebar fabrication and workshop training.
Wire Butt Welding Machine 10 kVA
Product code: CMI-NP-0927Buy Wire Butt Welding Machine 10 kVA from India
A 10 kVA resistance butt welding machine for joining wire and rod ends up to 6 mm diameter, used in wire drawing units and welding workshops.
Wire Butt Welding Machine 25 kVA
Product code: CMI-NP-0928Buy Wire Butt Welding Machine 25 kVA from India
A 25 kVA butt welding machine for steel wire and rod up to 12 mm diameter, used in wire product manufacture and training of resistance welding.
Wire Butt Welding Machine with Annealing Unit
Product code: CMI-NP-0929Buy Wire Butt Welding Machine with Annealing Unit from India
A butt welding machine with built in annealing circuit that softens the joint after welding, used for high carbon wire where weld hardness must be reduced.
Wire Butt Welding Machine range by function
| Function | Products | What to confirm |
|---|---|---|
| Wire and rod joining | Wire Butt Welding Machine 10 kVA, Wire Butt Welding Machine 25 kVA, Pneumatic Wire Butt Welding Machine 16 kVA | Maximum wire or rod diameter (6 mm to 12 mm class), kVA rating, 415 V supply, clamp die sizes and manual or air cylinder clamping |
| Rebar end joining | Rebar Butt Welding Machine 63 kVA | Bar diameter up to 25 mm, upset travel, flash welding cycle, three phase load and how the weld flash will be trimmed |
| High carbon wire joints | Wire Butt Welding Machine with Annealing Unit | Annealing current and timer range, wire grade, and the joint hardness you need after annealing |
How is this different from Bandsaw Butt Welding?
A bandsaw butt welder is made for thin saw blade strip: it has narrow jaws, a built in annealing step and a grinder to clean the weld flash to blade thickness. A wire butt welding machine clamps round wire, rod or rebar between copper dies and upsets the ends together, so die shape, kVA and clamp travel are different. The principle is the same, but the machines cannot stand in for each other.
See also: Bandsaw Butt Welding Suppliers
Full Wire Butt Welding Machine product list
The complete Wire Butt Welding Machine range (6 products), in alphabetical order:
Specifications and standards
How do I choose the kVA rating for a wire butt welding machine?
Start from the largest diameter you will join. Our 10 kVA machine handles wire and rod up to about 6 mm, the 25 kVA machine up to 12 mm, and the 63 kVA flash welder reinforcement bar up to 25 mm. Joining steel near the limit of a smaller machine gives cold joints, so leave headroom. Also confirm 415 V supply and breaker size.
When does wire need the annealing version?
High carbon and spring wire turns hard and brittle at the weld, so it snaps when drawn or coiled again. The annealing unit passes a lower, timed current through the joint after welding to soften it. Tell us the wire grade, diameter and the next process so the current and timer range can be set to match.
Manual clamping or pneumatic clamping?
Manual lever clamping is cheaper and fine for occasional joints in a workshop. Pneumatic clamping and upset, as on the 16 kVA machine, give the same pressure every cycle, which matters on a production line. It needs a clean air supply at the pressure we specify, so check your compressor first.
Who buys Wire Butt Welding Machine?
Wire drawing and wire product factories buy these machines to rejoin broken coils without stopping the line. Rebar fabricators use the 63 kVA model to extend bars end to end. Polytechnics and ITIs add one butt welder to a shop that already has arc, spot and MIG sets, so students see resistance welding alongside other processes.
Related ranges
Frequently asked questions
What is the difference between flash and resistance butt welding?
In resistance butt welding the ends are pressed together while current heats them. In flash butt welding an arc is struck between the ends first, then they are upset together. The 63 kVA rebar machine uses flash welding, which suits thick sections better than thin wire.
How much floor space and power does the 63 kVA machine need?
It draws a heavy three phase load, so check transformer capacity, cable size and breaker rating before ordering. Leave room around the machine for bar feeding and for trimming the flash. We give the footprint and connected load at quotation stage.
Can the joint strength be tested after welding?
A simple bend test on a sample joint shows whether the weld is sound, and a tension test on a universal testing machine gives the strength against parent wire. Many shops keep a few test coupons at every change of wire grade.
Do you ship wire butt welding machines outside India?
Yes, we export them as well as supplying within India. Quote the voltage and frequency of your plant, since 380 V or 440 V supplies change the transformer winding, and we will confirm packing for the transformer and dies.
Request a tender quotation
Civil Mechanical India is an established manufacturer and supplier for tender requirements from India, handling civil laboratory and industrial testing tenders and bulk and OEM orders for mechanical engineering and testing laboratory equipment. On receipt of your tender specifications, we will submit a complete quotation for Wire Butt Welding Machine.
- Civil laboratory & industrial testing tenders
- Mechanical engineering & testing lab equipment
- Bulk and OEM supply