export@civilmechanicalindia.com Exporting to 90+ countries IS · BS · EN · ASTM · AASHTO

3 Roll Plate Bending Machine Manufacturers and Suppliers in India

3 Roll Double Initial Pinch Plate Suppliers

Quick answer: A 3 roll plate bending machine rolls sheet and plate into cylinders and cones. Civil Mechanical India manufactures and supplies 3 roll double initial pinch machines, hydraulic and mechanical types, motorised pinch benders, ring rollers and hand operated units in India, with export on request.

Fabricators asking for 3 roll plate bending machine manufacturers in India usually give a plate thickness and width first. Civil Mechanical India is among the suppliers in India of three roll machines from small hand rollers to hydraulic plate rolls with double initial pinch.

A three roll machine bends plate between an upper roll and two lower rolls. In a double initial pinch design, the ends of the plate are pre-bent at both edges, which leaves little flat length and gives round shells. Models listed include hand operated rollers for thin sheet, motorised initial pinch benders, and mechanical and hydraulic plate rolls for thicker plate.

An angle section ring roller handles angles, tubes and flats. Buyers specify the rolling capacity (thickness and width), prebend capacity and roll diameter.

Last updated: November 2026

Angle Section Ring Roller

Product code: CMI-NP-0347
Buy Angle Section Ring Roller from India

A machine for bending angles, tubes and flats into rings. Used in fabrication. Features include profile rolls, geared drive and interchangeable.

Hand Operated Three Roll Bending Machine

Product code: CMI-NP-0348
Buy Hand Operated Three Roll Bending Machine from India

A hand cranked small roller for bending thin sheets and wire in training workshops. Used in sheet metal training. Features include hand cranked, light and compact and bench mounting.

Motorised Initial Pinch Three Roll Bender

Product code: CMI-NP-0349
Buy Motorised Initial Pinch Three Roll Bender from India

A motorised bender with initial pinch for rolling sheet and plate without flat ends. Used in sheet metal shops. Features include initial pinch action, motor drive and hardened rolls.

Three Roll Plate Bending Machine Hydraulic

Product code: CMI-NP-0350
Buy Three Roll Plate Bending Machine Hydraulic from India

A hydraulic plate roll that bends heavier plate with a hydraulic cylinder. Used in fabrication and boiler workshops. Features include hydraulic roll adjustment, hardened rolls and control panel.

Three Roll Plate Bending Machine Mechanical

Product code: CMI-NP-0351
Buy Three Roll Plate Bending Machine Mechanical from India

A mechanical bending machine with three rolls for rolling sheet metal into cylinders. Used in workshops and fabrication shops. Features include geared mechanical drive, hardened rolls and adjustable top roll.

3 Roll Plate Bending Machine range by function

FunctionProductsWhat to confirm
Double initial pinch rolls3 Roll Double Initial Pinch Plate, Motorised Initial Pinch Three Roll BenderRolling capacity (thickness x width), prebend capacity, roll diameters and drive motor.
Hydraulic and mechanical plate rollsThree Roll Plate Bending Machine Hydraulic, Three Roll Plate Bending Machine MechanicalPlate thickness in mild steel, drive type, roll length, and controls fitted.
Light and section bendingHand Operated Three Roll Bending Machine, Angle Section Ring RollerSheet gauge capacity, section sizes (angle, flat, tube), roll groove and minimum ring diameter.

How is 3 Roll Plate Bending Machine different from 4 Roll Double Initial Pinch Plate Suppliers?

A 3 roll machine bends plate with one pass-and-turn technique, and prebending is handled by the roll geometry or by an initial pinch design. A 4 roll machine has an extra side roll that grips the plate, so it can prebend and roll without removing the plate, which saves time on heavy jobs. Three roll machines suit general fabrication and are less costly, while four roll machines suit high volume or heavy plate work and demand more floor space.

See also: 4 Roll Double Initial Pinch Plate Suppliers

Full 3 Roll Plate Bending Machine product list

The complete 3 Roll Plate Bending Machine range (6 products), in alphabetical order:

Specifications and standards

What should be checked before ordering a 3 roll plate bending machine?

State the maximum plate thickness, width and material (mild steel or stainless), minimum cylinder diameter and whether cones are needed. Check roll diameter and hardening, drive (hydraulic, mechanical or manual), motor rating on 415 V supply, and safety features. Ask about the prebend capacity because this affects flat ends.

What does double initial pinch mean?

It means the plate edges can be pinched and bent at both ends with the rolls, forming a near perfect circle with minimal flat portions. This reduces rework and welding fit-up errors, and is helpful for tanks and pipes.

Who buys 3 Roll Plate Bending Machine?

Fabrication shops, boiler and pressure vessel makers, ITIs and polytechnics with sheet metal trades, tank and silo makers, and general engineering workshops buy plate bending machines. Colleges often buy a hand or motorised roller for training, while production shops buy hydraulic rolls, and many order with shears or press brakes.

Related ranges

Frequently asked questions

What is the difference between hydraulic and mechanical plate rolls?

Hydraulic rolls use cylinders to position rolls and give smooth, adjustable force. Mechanical rolls use screws and gears and cost less but need more manual setting.

Can a three roll machine make cones?

Yes, with a tilting or adjustable side roll and some care, cones can be rolled on many three roll machines, though it takes more skill than a cylinder. Mention cone size and plate thickness in your enquiry.

Do you supply plate rolls across India and for export?

Civil Mechanical India manufactures and supplies plate bending machines in India with delivery and installation support, and exports to other countries. Provide your plate capacity, drive type, quantity and destination in the enquiry.

Can you build a machine to my plate size?

Machines are offered in a range of standard capacities, and custom capacities can be discussed with our team. Send the plate thickness, width, material and diameters you need so a suitable size can be proposed.

Tender enquiries

Request a tender quotation

We are leading manufacturers and suppliers for tender requirements from India, serving civil laboratory and industrial testing tenders and supplying mechanical engineering and testing laboratory equipment in bulk and on OEM terms. Send us your tender specifications, and a complete quotation for 3 Roll Plate Bending Machine will be prepared accordingly.

  • Civil laboratory & industrial testing tenders
  • Mechanical engineering & testing lab equipment
  • Bulk and OEM supply
Send Tender Specifications Quotation prepared against your tender specifications
Get a quotation

Planning a civil engineering laboratory or replying to a tender?

Send us your equipment list or tender specification. We quote against IS, BS, EN, ASTM and AASHTO standards and ship to 90+ countries.