export@civilmechanicalindia.com Exporting to 90+ countries IS · BS · EN · ASTM · AASHTO

Hydraulic Thread And Form Rolling Manufacturers and Suppliers in India

Hydraulic Thread And Form Rolling Suppliers

Quick answer: Hydraulic thread and form rolling machines make threads by pressing hardened dies into a bolt blank rather than cutting. The range has 6 and 12 tonne thread rollers, a flat die machine, a spline form rolling machine and a pipe end form rolling machine. Civil Mechanical India makes these rolling machines and supplies them to Indian buyers.

Fastener makers and production trainers looking for hydraulic thread and form rolling manufacturers in India need to match workpiece diameter and thread pitch to machine tonnage. Civil Mechanical India is one of the suppliers in India that lists machines of 6 and 12 tonne and workpiece ranges from 3 to 80 mm.

Thread rolling displaces metal instead of cutting it. A blank is pressed between dies, so the thread form is raised from the core, the grain flows with the profile and the thread is stronger and smoother than a cut thread. The main machine in this range takes work of 3 to 24, 3 to 50 and 10 to 80 mm with a thread pitch up to 3, 5 and 10 mm.

The 6 tonne machine suits rods and bolts, and the 12 tonne machine takes larger studs. The flat die machine, with a moving and a fixed die, is used for high volume small screws. Form rolling machines make splines and knurls on shafts and rolled grooves and beads on pipe ends for grooved joints.

Last updated: November 2026

Hydraulic Flat Die Thread Rolling Machine

Product code: CMI-NP-0636
Buy Hydraulic Flat Die Thread Rolling Machine from India

Machine using a moving and fixed flat die to roll threads on small screws and bolts. Used for high volume screw production training. Main ratings: capacity M3 to M10, stroke 300 mm, motor 3 HP, 415 V AC.

Hydraulic Form Rolling Machine For Splines

Product code: CMI-NP-0637
Buy Hydraulic Form Rolling Machine For Splines from India

Machine for forming splines and knurls on shafts by rolling. Used in demonstrations of form rolling processes. Main ratings: max diameter 40 mm, roll force 10 tonne, motor 5 HP, 415 V AC.

Hydraulic Pipe End Form Rolling Machine

Product code: CMI-NP-0638
Buy Hydraulic Pipe End Form Rolling Machine from India

Machine that rolls grooves and beads on pipe ends. Used in plumbing and HVAC training for grooved joints. Main ratings: pipe size 1 to 4 inch, motor 2 HP, 415 V AC, roll Grooving.

Hydraulic Thread Rolling Machine 12 Tonne

Product code: CMI-NP-0639
Buy Hydraulic Thread Rolling Machine 12 Tonne from India

Heavier thread rolling machine for larger diameter bolts and studs. Used in labs to demonstrate rolled thread production on bigger sizes. Main ratings: capacity M10 to M20, roll force 12 tonne, motor 5 HP, 415 V AC.

Hydraulic Thread Rolling Machine 6 Tonne

Product code: CMI-NP-0640
Buy Hydraulic Thread Rolling Machine 6 Tonne from India

Hydraulic machine that forms external threads on bolts and rods by rolling between flat or round dies. Used in production training to show cold forming of threads without cutting.

Hydraulic Thread And Form Rolling range by function

FunctionProductsWhat to confirm
Thread rollingHydraulic Thread Rolling Machine 6 Tonne, Hydraulic Thread Rolling Machine 12 Tonne, Hydraulic Thread And Form RollingWorkpiece diameter, maximum pitch, rolling force and die set size
Flat die rollingHydraulic Flat Die Thread Rolling MachineScrew diameter range, die length, output per minute and blank feeding method
Form and end rollingHydraulic Form Rolling Machine For Splines, Hydraulic Pipe End Form Rolling MachineSpline or groove profile, pipe diameter range, die tooling and cycle length

How is this different from the Hex Nipple Threading Machine?

A hex nipple machine cuts threads with a die head, removing metal as chips. A thread rolling machine does not cut anything. It cold forms the thread by pressing, which gives stronger threads and no chips, but it needs a blank turned to the pitch diameter. Choose rolling for bolts and studs in volume and cutting for pipe nipples.

See also: Hex Nipple Threading Machine Suppliers

Full Hydraulic Thread And Form Rolling product list

The complete Hydraulic Thread And Form Rolling range (6 products), in alphabetical order:

Specifications and standards

How do I choose tonnage and die size?

Choose by the largest thread diameter and pitch, and the material. Higher strength steel needs more force. Give us the diameter, pitch and steel grade, and we check against 6 or 12 tonne ratings. Die set sizes should be listed one per thread size.

What blank preparation is needed?

The blank diameter should be close to the pitch diameter of the thread, which is smaller than the major diameter. Poor blank size results in incomplete thread or die damage. Ask for guidance on blank sizes for your thread standard.

What should a training lab check?

A lab needs a clear guard, pressure gauge, die setting jig and a roller inspection routine. Demonstrating rolled versus cut threads with a section microscope is a useful classroom exercise. Check also that the die setting is shown with a simple jig, so students can learn to align the two dies parallel before each run.

Who buys Hydraulic Thread And Form Rolling?

Typical buyers are bolt and screw manufacturers, forging and fastener units, pipe and HVAC fabricators for grooved ends, and technical colleges teaching metal forming. Vocational centres also buy form rolling machines to demonstrate spline and knurl production. Rolled studs and screws are also needed by anchor and fastener makers, who buy these presses with die sets for a particular thread series.

Related ranges

Frequently asked questions

Why is a rolled thread stronger than a cut thread?

The grain flows along the thread profile and the surface is work hardened. A cut thread severs the grain, so fatigue strength is lower. This also gives smoother thread flanks, and the rolled core is stronger in tension, which is why high strength bolts are rolled.

Do I need different dies for each pitch?

Yes, dies are made for a particular thread form and pitch. Order die sets with the machine. A die set made for a metric 1.5 mm pitch cannot roll a 2 mm pitch, so spare sets should be priced with the machine at the start.

What does the pipe end form rolling machine make?

It rolls grooves and beads on pipe ends, used in grooved coupling joints in plumbing and HVAC. The same machine can be used to put beads and grooves on pipe ends that take quick couplers or clamps in pipelines and ducts.

Is oil needed during rolling?

Yes, a lubricating coolant reduces die wear and gives a smooth surface. The oil also carries away heat and fine particles from the die faces, and should be filtered and replaced at the interval stated in the manual.

Are machines exported?

Yes, please share the destination, voltage and tooling needs. These presses are heavy, so crate weight is stated in advance, and spare die sets can be packed in the same shipment.

Tender enquiries

Request a tender quotation

As established manufacturers and suppliers for tender requirements from India, we undertake civil laboratory and industrial testing tenders as well as bulk and OEM supply of mechanical engineering and testing laboratory equipment. Please forward your tender specifications and our team will prepare a detailed quotation for Hydraulic Thread And Form Rolling.

  • Civil laboratory & industrial testing tenders
  • Mechanical engineering & testing lab equipment
  • Bulk and OEM supply
Send Tender Specifications Quotation prepared against your tender specifications
Get a quotation

Planning a civil engineering laboratory or replying to a tender?

Send us your equipment list or tender specification. We quote against IS, BS, EN, ASTM and AASHTO standards and ship to 90+ countries.